mirror of
https://github.com/hsoft/collapseos.git
synced 2024-11-17 08:38:05 +11:00
31119c2de3
I'd like to move this code, along with all recipe contents, to blk/. It's easier if "emul-related" code is gathered at the same place.
90 lines
4.0 KiB
Markdown
90 lines
4.0 KiB
Markdown
# Assembling Collapse OS from within it
|
|
|
|
This is where we tie lose ends, complete the circle, loop the loop: we assemble
|
|
a new Collapse OS *entirely* from within Collapse OS and write it to EEPROM,
|
|
either for another RC2014 or for an OS upgrade.
|
|
|
|
## Gathering parts
|
|
|
|
* stage3 from `sdcard` recipe. If you want to write to EEPROM as the final step,
|
|
you'll need a hybrid stage3 that also includes stuff from the `eeprom` recipe.
|
|
|
|
## Building stage 1
|
|
|
|
Build Collapse OS' stage 1 from within Collapse OS is very similar to how we do
|
|
it from the makefile. If you take the time to look at the base recipe
|
|
`Makefile`, you'll see `cat xcomp.fs | $(STAGE2)`. That's the thing. Open
|
|
`xcomp.fs` in a text editor and take a look at it.
|
|
|
|
To assemble stage 1 from RC2014, all you need to do is to type those commands
|
|
in the same order, and replace the `/MOD 2 PC! 2 PC!` words with `.X`.
|
|
Those commands will inform you of the begin/end offsets of the assembled binary.
|
|
|
|
I'm not going to explain in detail what each command do, but only give you an
|
|
overview of what is happening. You are encouraged to read the in-system
|
|
documentation for more information.
|
|
|
|
The first part is configuration of your new system. When RAM starts, where RSP
|
|
starts, what ports to use for what device, etc. These configuration declarations
|
|
are expected in the boot code and driver code.
|
|
|
|
Then, we load the Z80 assembler and the cross compiler (xcomp for short), which
|
|
we'll of course need for the task ahead.
|
|
|
|
Then come xcomp overrides, which are needed for xcomp to be effective.
|
|
|
|
At this point, we're about to begin spitting binary content, this will be our
|
|
starting offset. `ORG` will soon be set to your current `H@`.
|
|
|
|
Then, we assemble the boot binary, drivers' native words, then inner core,
|
|
close the binary with a hook word. We're finished with cross-compiling.
|
|
|
|
We're at the offset that will be `CURRENT` on boot, so we update `LATEST`.
|
|
|
|
Then, we spit the source code that will be interpreted by stage 1 on boot so
|
|
that it bootstraps itself to a full interpreter. Not all units are there
|
|
because they don't fit in 8K, but they're sufficient for our needs. We also
|
|
need the linker so that we can relink ourselves to stage 2.
|
|
|
|
Finally, we have initialization code, then a spit of the ending offset.
|
|
|
|
Go ahead, run that. However, one thing you should know is that because the SD
|
|
card driver is a bit slow, some of these commands take a long time. Multiple
|
|
minutes. Be patient.
|
|
|
|
Once all your commands are run and that you have your begin/end offset (write
|
|
them down somewhere), you're at the same point as you were after the `make`
|
|
part of the base recipe. The contents between your start and end offset is the
|
|
exact same as the contents of `stage1.bin` when you run `make`. Continue your
|
|
deployment from there.
|
|
|
|
Good luck!
|
|
|
|
### What to do on SDerr?
|
|
|
|
If you get `SDerr` in the middle of a LOAD operation, something went wrong with
|
|
the SD card. The bad news is that it left your xcomp operation in an
|
|
inconsistent state. If your at the beginning of it, it's easier to restart it
|
|
entirely.
|
|
|
|
If you're towards the end, you might want to repair it. To do so, you'll have to
|
|
bring your `XCURRENT` and `HERE` values to where they were before the LOAD
|
|
operation. You could have thought ahead and printed them before the LOAD, but if
|
|
you didn't, you'll just have to dig in your memory with `DUMP`.
|
|
|
|
You're looking at the offset of the last wordref of the *previous* LOAD
|
|
operation. That offset is going in `XCURRENT`. Then, you're looking at the end
|
|
of that word. That offset goes in `HERE`. Once you've done that, relaunch your
|
|
LOAD.
|
|
|
|
### Verifying
|
|
|
|
You can use `/tools/memdump` to dump the memory between your begin/end offsets
|
|
so that you can compare against your reference stage 1. Before you do, you have
|
|
to take yourself out of xcomp mode. First, run `XCOFF` to go back to your
|
|
regular dict. Then, run `FORGET CODE` to undo the xcomp overrides you've added
|
|
before. That will rewind `HERE`. You don't want that. Put `HERE` back to after
|
|
your ending offset so that you don't overwrite your binary.
|
|
|
|
Then, you can run `/tools/memdump`.
|