mirror of
https://github.com/hsoft/collapseos.git
synced 2024-11-08 19:58:08 +11:00
505 lines
11 KiB
NASM
505 lines
11 KiB
NASM
; sdc
|
|
;
|
|
; Manages the initialization of a SD card and implement a block device to read
|
|
; and write from/to it, in SPI mode.
|
|
;
|
|
; Note that SPI can't really be used directly from the z80, so this part
|
|
; assumes that you have a device that handles SPI communication on behalf of
|
|
; the z80. This device is assumed to work in a particular way. See the
|
|
; "rc2014/sdcard" recipe for details.
|
|
;
|
|
; That device has 3 ports. One write-only port to make CS high, one to make CS
|
|
; low (data sent is irrelevant), and one read/write port to send and receive
|
|
; bytes with the card through the SPI protocol. The device acts as a SPI master
|
|
; and writing to that port initiates a byte exchange. Data from the slave is
|
|
; then placed on a buffer that can be read by reading the same port.
|
|
;
|
|
; It's through that kind of device that this code below is supposed to work.
|
|
|
|
; *** Defines ***
|
|
; SDC_PORT_CSHIGH: Port number to make CS high
|
|
; SDC_PORT_CSLOW: Port number to make CS low
|
|
; SDC_PORT_SPI: Port number to send/receive SPI data
|
|
|
|
; *** Consts ***
|
|
.equ SDC_BLKSIZE 512
|
|
|
|
; *** Variables ***
|
|
; Where the block dev current points to. This is a byte index. Higher 7 bits
|
|
; indicate a sector number, lower 9 bits are an offset in the current SDC_BUF.
|
|
.equ SDC_PTR SDC_RAMSTART
|
|
; Whenever we read a sector, we read a whole block at once and we store it
|
|
; in memory. That's where it goes.
|
|
.equ SDC_BUF SDC_PTR+2
|
|
; Sector number currently in SDC_BUF. 0xff, it's initial value, means "no
|
|
; sector.
|
|
.equ SDC_BUFSEC SDC_BUF+SDC_BLKSIZE
|
|
; Whether the buffer has been written to. 0 means clean. 1 means dirty.
|
|
.equ SDC_BUFDIRTY SDC_BUFSEC+1
|
|
.equ SDC_RAMEND SDC_BUFDIRTY+1
|
|
|
|
; *** Code ***
|
|
; Wake the SD card up. After power up, a SD card has to receive at least 74
|
|
; dummy clocks with CS and DI high. We send 80.
|
|
sdcWakeUp:
|
|
out (SDC_PORT_CSHIGH), a
|
|
ld b, 10 ; 10 * 8 == 80
|
|
ld a, 0xff
|
|
.loop:
|
|
out (SDC_PORT_SPI), a
|
|
nop
|
|
djnz .loop
|
|
ret
|
|
|
|
; Initiate SPI exchange with the SD card. A is the data to send. Received data
|
|
; is placed in A.
|
|
sdcSendRecv:
|
|
out (SDC_PORT_SPI), a
|
|
nop
|
|
nop
|
|
in a, (SDC_PORT_SPI)
|
|
nop
|
|
nop
|
|
ret
|
|
|
|
sdcIdle:
|
|
ld a, 0xff
|
|
jp sdcSendRecv
|
|
|
|
; sdcSendRecv 0xff until the response is something else than 0xff for a maximum
|
|
; of 20 times. Returns 0xff if no response.
|
|
sdcWaitResp:
|
|
push bc
|
|
ld b, 20
|
|
.loop:
|
|
call sdcIdle
|
|
inc a ; if 0xff, it's going to become zero
|
|
jr nz, .end ; not zero? good, that's our command
|
|
djnz .loop
|
|
.end:
|
|
; whether we had a success or failure, we return the result.
|
|
; But first, let's bring it back to its original value.
|
|
dec a
|
|
pop bc
|
|
ret
|
|
|
|
; Sends a command to the SD card, along with arguments and specified CRC fields.
|
|
; (CRC is only needed in initial commands though).
|
|
; A: Command to send
|
|
; H: Arg 1 (MSB)
|
|
; L: Arg 2
|
|
; D: Arg 3
|
|
; E: Arg 4 (LSB)
|
|
; C: CRC
|
|
;
|
|
; Returns R1 response in A.
|
|
;
|
|
; This does *not* handle CS. You have to select/deselect the card outside this
|
|
; routine.
|
|
sdcCmd:
|
|
; Wait until ready to receive commands
|
|
push af
|
|
call sdcWaitResp
|
|
pop af
|
|
|
|
call sdcSendRecv
|
|
; Arguments
|
|
ld a, h
|
|
call sdcSendRecv
|
|
ld a, l
|
|
call sdcSendRecv
|
|
ld a, d
|
|
call sdcSendRecv
|
|
ld a, e
|
|
call sdcSendRecv
|
|
; send CRC
|
|
ld a, c
|
|
call sdcSendRecv
|
|
|
|
; And now we just have to wait for a valid response...
|
|
jp sdcWaitResp ; return
|
|
|
|
; Send a command that expects a R1 response, handling CS.
|
|
sdcCmdR1:
|
|
out (SDC_PORT_CSLOW), a
|
|
call sdcCmd
|
|
out (SDC_PORT_CSHIGH), a
|
|
ret
|
|
|
|
; Send a command that expects a R7 response, handling CS. A R7 is a R1 followed
|
|
; by 4 bytes. Those 4 bytes are returned in HL/DE in the same order as in
|
|
; sdcCmd.
|
|
sdcCmdR7:
|
|
out (SDC_PORT_CSLOW), a
|
|
call sdcCmd
|
|
|
|
; We have our R1 response in A. Let's try reading the next 4 bytes in
|
|
; case we have a R3.
|
|
push af
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld h, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld l, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld d, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld e, a
|
|
pop af
|
|
|
|
out (SDC_PORT_CSHIGH), a
|
|
ret
|
|
|
|
; Initialize a SD card. This should be called at least 1ms after the powering
|
|
; up of the card. Sets result code in A. Zero means success, non-zero means
|
|
; error.
|
|
sdcInitialize:
|
|
push hl
|
|
push de
|
|
push bc
|
|
call sdcWakeUp
|
|
|
|
; Call CMD0 and expect a 0x01 response (card idle)
|
|
; This should be called multiple times. We're actually expected to.
|
|
; Let's call this for a maximum of 10 times.
|
|
ld b, 10
|
|
.loop1:
|
|
ld a, 0b01000000 ; CMD0
|
|
ld hl, 0
|
|
ld de, 0
|
|
ld c, 0x95
|
|
call sdcCmdR1
|
|
cp 0x01
|
|
jp z, .cmd0ok
|
|
djnz .loop1
|
|
; Nothing? error
|
|
jr .error
|
|
.cmd0ok:
|
|
|
|
; Then comes the CMD8. We send it with a 0x01aa argument and expect
|
|
; a 0x01aa argument back, along with a 0x01 R1 response.
|
|
ld a, 0b01001000 ; CMD8
|
|
ld hl, 0
|
|
ld de, 0x01aa
|
|
ld c, 0x87
|
|
call sdcCmdR7
|
|
cp 0x01
|
|
jr nz, .error
|
|
xor a
|
|
cp h ; H is zero
|
|
jr nz, .error
|
|
cp l ; L is zero
|
|
jr nz, .error
|
|
ld a, d
|
|
cp 0x01
|
|
jp nz, .error
|
|
ld a, e
|
|
cp 0xaa
|
|
jr nz, .error
|
|
|
|
; Now we need to repeatedly run CMD55+CMD41 (0x40000000) until we
|
|
; the card goes out of idle mode, that is, when it stops sending us
|
|
; 0x01 response and send us 0x00 instead. Any other response means that
|
|
; initialization failed.
|
|
.loop2:
|
|
ld a, 0b01110111 ; CMD55
|
|
ld hl, 0
|
|
ld de, 0
|
|
call sdcCmdR1
|
|
cp 0x01
|
|
jr nz, .error
|
|
ld a, 0b01101001 ; CMD41 (0x40000000)
|
|
ld hl, 0x4000
|
|
ld de, 0x0000
|
|
call sdcCmdR1
|
|
cp 0x01
|
|
jr z, .loop2
|
|
or a ; cp 0
|
|
jr nz, .error
|
|
; Success! out of idle mode!
|
|
; initialize variables
|
|
ld hl, 0
|
|
ld (SDC_PTR), hl
|
|
ld a, 0xff
|
|
ld (SDC_BUFSEC), a
|
|
xor a
|
|
ld (SDC_BUFDIRTY), a
|
|
jr .end
|
|
|
|
.error:
|
|
ld a, 0x01
|
|
.end:
|
|
pop bc
|
|
pop de
|
|
pop hl
|
|
ret
|
|
|
|
; Send a command to set block size to SDC_BLKSIZE to the SD card.
|
|
; Returns zero in A if a success, non-zero otherwise
|
|
sdcSetBlkSize:
|
|
push hl
|
|
push de
|
|
|
|
ld a, 0b01010000 ; CMD16
|
|
ld hl, 0
|
|
ld de, SDC_BLKSIZE
|
|
call sdcCmdR1
|
|
; Since we're out of idle mode, we expect a 0 response
|
|
; We need no further processing: A is already the correct value.
|
|
pop de
|
|
pop hl
|
|
ret
|
|
|
|
; Read block index specified in A and place the contents in (SDC_BUF).
|
|
; Doesn't check CRC. If the operation is a success, updates (SDC_BUFSEC) to the
|
|
; value of A.
|
|
; Returns 0 in A if success, non-zero if error.
|
|
sdcReadBlk:
|
|
push bc
|
|
push hl
|
|
|
|
out (SDC_PORT_CSLOW), a
|
|
ld hl, 0 ; read single block at addr A
|
|
ld d, 0
|
|
ld e, a ; E isn't touched in the rest of the routine
|
|
; and holds onto our original A
|
|
ld a, 0b01010001 ; CMD17
|
|
call sdcCmd
|
|
or a ; cp 0
|
|
jr nz, .error
|
|
|
|
; Command sent, no error, now let's wait for our data response.
|
|
ld b, 20
|
|
.loop1:
|
|
call sdcWaitResp
|
|
; 0xfe is the expected data token for CMD17
|
|
cp 0xfe
|
|
jr z, .loop1end
|
|
cp 0xff
|
|
jr nz, .error
|
|
djnz .loop1
|
|
jr .error ; timeout. error out
|
|
.loop1end:
|
|
; We received our data token!
|
|
; Data packets follow immediately, we have 512 of them to read
|
|
ld bc, SDC_BLKSIZE
|
|
ld hl, SDC_BUF
|
|
.loop2:
|
|
call sdcIdle
|
|
ld (hl), a
|
|
cpi ; a trick to inc HL and dec BC at the same time.
|
|
; P/V indicates whether BC reached 0
|
|
jp pe, .loop2 ; BC is not zero, loop
|
|
; Read our 2 CRC bytes
|
|
call sdcIdle
|
|
call sdcIdle
|
|
; success! Let's recall our orginal A arg and put it in SDC_BUFSEC
|
|
ld a, e
|
|
ld (SDC_BUFSEC), a
|
|
xor a
|
|
ld (SDC_BUFDIRTY), a
|
|
jr .end
|
|
.error:
|
|
; try to preserve error code
|
|
or a ; cp 0
|
|
jr nz, .end ; already non-zero
|
|
inc a ; zero, adjust
|
|
.end:
|
|
out (SDC_PORT_CSHIGH), a
|
|
pop hl
|
|
pop bc
|
|
ret
|
|
|
|
; Write the contents of (SDC_BUF) in sector number (SDC_BUFSEC). Unsets the
|
|
; (SDC_BUFDIRTY) flag on success.
|
|
; A returns 0 in A on success (with Z set), non-zero (with Z unset) on error.
|
|
sdcWriteBlk:
|
|
ld a, (SDC_BUFDIRTY)
|
|
or a ; cp 0
|
|
ret z ; return success, but do nothing.
|
|
|
|
push bc
|
|
push hl
|
|
|
|
out (SDC_PORT_CSLOW), a
|
|
ld a, (SDC_BUFSEC)
|
|
ld hl, 0 ; write single block at addr A
|
|
ld d, 0
|
|
ld e, a
|
|
ld a, 0b01011000 ; CMD24
|
|
call sdcCmd
|
|
or a ; cp 0
|
|
jr nz, .error
|
|
|
|
; Before sending the data packet, we need to send at least one empty
|
|
; byte.
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
|
|
; data packet token for CMD24
|
|
ld a, 0xfe
|
|
call sdcSendRecv
|
|
|
|
; Sending our data token!
|
|
ld bc, SDC_BLKSIZE
|
|
ld hl, SDC_BUF
|
|
.loop:
|
|
ld a, (hl)
|
|
call sdcSendRecv
|
|
cpi ; a trick to inc HL and dec BC at the same time.
|
|
; P/V indicates whether BC reached 0
|
|
jp pe, .loop ; BC is not zero, loop
|
|
; Send our 2 CRC bytes. They can be anything
|
|
call sdcIdle
|
|
call sdcIdle
|
|
; Let's see what response we have
|
|
call sdcWaitResp
|
|
and 0b00011111 ; We ignore the first 3 bits of the response.
|
|
cp 0b00000101 ; A valid response is "010" in bits 3:1 flanked
|
|
; by 0 on its left and 1 on its right.
|
|
jr nz, .error
|
|
; good! Now, we need to let the card process this data. It will return
|
|
; 0xff when it's not busy any more.
|
|
call sdcWaitResp
|
|
xor a
|
|
ld (SDC_BUFDIRTY), a
|
|
jr .end
|
|
.error:
|
|
; try to preserve error code
|
|
or a ; cp 0
|
|
jr nz, .end ; already non-zero
|
|
inc a ; zero, adjust
|
|
.end:
|
|
out (SDC_PORT_CSHIGH), a
|
|
pop hl
|
|
pop bc
|
|
ret
|
|
|
|
; Ensures that (SDC_BUFSEC) is in sync with (SDC_PTR), that is, that the current
|
|
; buffer in memory corresponds to where SDC_PTR points to. If it doesn't, loads
|
|
; the sector that (SDC_PTR) points to in (SDC_BUF) and update (SDC_BUFSEC).
|
|
; If the (SDC_BUFDIRTY) flag is set, we write the content of the in-memory
|
|
; buffer to the SD card before we read a new sector.
|
|
; Returns Z on success, not-Z on error (with the error code from either
|
|
; sdcReadBlk or sdcWriteBlk)
|
|
sdcSync:
|
|
; SDC_PTR points to the character we're supposed to read or right now,
|
|
; but we first have to check whether we need to load a new sector in
|
|
; memory. To do this, we compare the high 7 bits of (SDC_PTR) with
|
|
; (SDC_BUFSEC). If they're different, we need to load a new block.
|
|
push hl
|
|
ld a, (SDC_BUFSEC)
|
|
ld h, a
|
|
ld a, (SDC_PTR+1) ; high byte has bufsec in its high 7 bits
|
|
srl a
|
|
cp h
|
|
pop hl
|
|
ret z ; equal? nothing to do
|
|
; We have to read a new sector, but first, let's write the current one
|
|
; if needed.
|
|
call sdcWriteBlk
|
|
ret nz ; error
|
|
; Let's read our new sector
|
|
ld a, (SDC_PTR+1)
|
|
srl a
|
|
jp sdcReadBlk ; returns
|
|
|
|
|
|
; *** shell cmds ***
|
|
|
|
sdcInitializeCmd:
|
|
.db "sdci", 0, 0, 0
|
|
call sdcInitialize
|
|
jp sdcSetBlkSize ; returns
|
|
|
|
; Flush the current SDC buffer if dirty
|
|
sdcFlushCmd:
|
|
.db "sdcf", 0, 0, 0
|
|
jp sdcWriteBlk ; returns
|
|
|
|
; *** blkdev routines ***
|
|
|
|
; Make HL point to (SDC_PTR) in current buffer
|
|
_sdcPlaceBuf:
|
|
call sdcSync
|
|
ret nz ; error
|
|
ld a, (SDC_PTR+1) ; high byte
|
|
and 0x01 ; is first bit set?
|
|
jr nz, .highbuf ; first bit set? we're in the "highbuf" zone.
|
|
; lowbuf zone
|
|
; Read byte from memory at proper offset in lowbuf (first 0x100 bytes)
|
|
ld hl, SDC_BUF
|
|
jr .read
|
|
.highbuf:
|
|
; Read byte from memory at proper offset in highbuf (0x100-0x1ff)
|
|
ld hl, SDC_BUF+0x100
|
|
.read:
|
|
; HL is now placed either on the lower or higher half of SDC_BUF and
|
|
; all we need is to increase HL by the number in SDC_PTR's LSB (little
|
|
; endian, remember).
|
|
ld a, (SDC_PTR) ; LSB
|
|
call addHL ; returns
|
|
xor a ; ensure Z
|
|
ret
|
|
|
|
sdcGetC:
|
|
push hl
|
|
call _sdcPlaceBuf
|
|
jr nz, .error
|
|
|
|
; This is it!
|
|
ld a, (hl)
|
|
|
|
; before we return A, we need to increase (SDC_PTR)
|
|
ld hl, (SDC_PTR)
|
|
inc hl
|
|
ld (SDC_PTR), hl
|
|
|
|
cp a ; ensure Z
|
|
jr .end
|
|
.error:
|
|
call unsetZ
|
|
.end:
|
|
pop hl
|
|
ret
|
|
|
|
sdcPutC:
|
|
push hl
|
|
push af ; let's remember the char we put, _sdcPlaceBuf
|
|
; destroys A.
|
|
call _sdcPlaceBuf
|
|
jr nz, .error
|
|
|
|
; HL points to our dest. Recall A and write
|
|
pop af
|
|
ld (hl), a
|
|
|
|
|
|
; we need to increase (SDC_PTR)
|
|
ld hl, (SDC_PTR)
|
|
inc hl
|
|
ld (SDC_PTR), hl
|
|
|
|
ld a, 1
|
|
ld (SDC_BUFDIRTY), a
|
|
xor a ; ensure Z
|
|
jr .end
|
|
.error:
|
|
pop af
|
|
call unsetZ
|
|
.end:
|
|
pop hl
|
|
ret
|
|
|
|
sdcSeek:
|
|
ld (SDC_PTR), hl
|
|
ret
|
|
|
|
sdcTell:
|
|
ld hl, (SDC_PTR)
|
|
ret
|
|
|