mirror of
https://github.com/hsoft/collapseos.git
synced 2024-11-15 15:38:05 +11:00
242 lines
6.7 KiB
NASM
242 lines
6.7 KiB
NASM
.include "tn45def.inc"
|
|
|
|
; Receives keystrokes from PS/2 keyboard and send them to the 595. As long as
|
|
; that number is not collected, we buffer the scan code received from ps/2. As
|
|
; soon as that number is collected we put the next number in the buffer. If the
|
|
; buffer is empty, we do nothing (the 595 already had its SRCLR pin triggered
|
|
; and shows 0).
|
|
;
|
|
; PS/2 is a bidirectional protocol, but in this program, we only care about
|
|
; receiving keystrokes. We don't send anything to the keyboard.
|
|
;
|
|
; The PS/2 keyboard has two data wires: Clock and Data. It is the keyboard that
|
|
; drives the clock with about 30-50 us between each clock.
|
|
;
|
|
; We wire the Clock to INT0 (PB2) and make it trigger an interrupt on the
|
|
; falling edge (the edge, in the PS/2 protocol, when data is set).
|
|
;
|
|
; Data is sent by the keyboard in 11-bit frames. 1 start bit (0), 8 data bits,
|
|
; one parity bit, one stop bit (1).
|
|
;
|
|
; Parity bit is set if number of bits in data bits is even. Unset otherwise.
|
|
;
|
|
; *** Receiving a data frame ***
|
|
;
|
|
; In idle mode, R18 is zero. When INT0 is triggered, it is increased and R17 is
|
|
; loaded with 0x80. We do this because we're going to right shift our data in
|
|
; (byte is sent LSB first). When the carry flag is set, we'll know we're
|
|
; finished. When that happens, we increase R18 again. We're waiting for parity
|
|
; bit. When we get it, we check parity and increase R18 again. We're waiting
|
|
; for stop bit. After we receive stop bit, we reset R18 to 0.
|
|
;
|
|
; On error, we ignore and reset our counters.
|
|
|
|
; *** Buffering scan codes ***
|
|
;
|
|
; The whole SRAM (from SRAM_START to RAMEND) is used as a scan code buffer, with
|
|
; Z chasing Y. When Y == Z, the buffer is empty. When RAMEND is reached, we go
|
|
; back to SRAM_START.
|
|
;
|
|
; Whenever a new scan code is received, we place it in Y and increase it.
|
|
; Whenever we send a scan code to the 595 (which can't be done when Z == Y
|
|
; because Z points to an invalid value), we send the value of Z and increase.
|
|
|
|
; *** Sending to the 595 ***
|
|
;
|
|
; Whenever a scan code is read from the 595, CE goes low and triggers a PCINT
|
|
; on PB4. When we get it, we clear the R2 flag to indicate that we're ready to
|
|
; send a new scan code to the 595.
|
|
;
|
|
; Because that CE flip/flop is real fast (375ns), it requires us to run at 8MHz.
|
|
;
|
|
; During the PCINT, we also trigger RCLK once because CE is also wired to SRCLR
|
|
; and we want the z80 to be able to know that the device has nothing to give
|
|
; (has a value of zero) rather than having to second guess (is this value, which
|
|
; is the same as the one that was read before, a new value or not?). With that
|
|
; "quick zero-in" scheme, there's no ambiguity: no scan code can be ready twice
|
|
; because it's replaced by a 0 as soon as it's read, until it can be filled with
|
|
; the next char in the buffer.
|
|
|
|
; *** Register Usage ***
|
|
;
|
|
; R1: when set, indicates that value in R17 is valid
|
|
; R2: When set, indicate that the 595 holds a value that hasn't been read by the
|
|
; z80 yet.
|
|
; R16: tmp stuff
|
|
; R17: recv buffer. Whenever we receive a bit, we push it in there.
|
|
; R18: recv step:
|
|
; - 0: idle
|
|
; - 1: receiving data
|
|
; - 2: awaiting parity bit
|
|
; - 3: awaiting stop bit
|
|
; it reaches 11, we know we're finished with the frame.
|
|
; R19: when set, indicates that the DATA pin was high when we received a bit
|
|
; through INT0. When we receive a bit, we set flag T to indicate it.
|
|
; R20: data being sent to the 595
|
|
; Y: pointer to the memory location where the next scan code from ps/2 will be
|
|
; written.
|
|
; Z: pointer to last scan code pushed to the 595
|
|
;
|
|
; *** Constants ***
|
|
;
|
|
.equ CLK = PINB2
|
|
.equ DATA = PINB1
|
|
.equ SRCLK = PINB3
|
|
.equ CE = PINB4
|
|
.equ RCLK = PINB0
|
|
|
|
rjmp main
|
|
rjmp hdlINT0
|
|
rjmp hdlPCINT
|
|
|
|
; Read DATA and set R19 if high. Then, set flag T.
|
|
; no SREG fiddling because no SREG-modifying instruction
|
|
hdlINT0:
|
|
sbic PINB, DATA ; DATA clear? skip next
|
|
ser r19
|
|
set
|
|
reti
|
|
|
|
; Only PB4 is hooked to PCINT and we don't bother checking the value of the PB4
|
|
; pin: things go too fast for this.
|
|
hdlPCINT:
|
|
; SRCLR has been triggered. Let's trigger RCLK too.
|
|
sbi PORTB, RCLK
|
|
cbi PORTB, RCLK
|
|
clr r2 ; 595 is now free
|
|
|
|
main:
|
|
ldi r16, low(RAMEND)
|
|
out SPL, r16
|
|
ldi r16, high(RAMEND)
|
|
out SPH, r16
|
|
|
|
; Set clock prescaler to 1 (8MHz)
|
|
ldi r16, (1<<CLKPCE)
|
|
out CLKPR, r16
|
|
clr r16
|
|
out CLKPR, r16
|
|
|
|
|
|
; init variables
|
|
clr r1
|
|
clr r2
|
|
clr r19
|
|
clr r18
|
|
|
|
; Setup int0/PCINT
|
|
; INT0, falling edge
|
|
ldi r16, (1<<ISC01)
|
|
out MCUCR, r16
|
|
; Enable both INT0 and PCINT
|
|
ldi r16, (1<<INT0)|(1<<PCIE)
|
|
out GIMSK, r16
|
|
; For PCINT, enable only PB4
|
|
ldi r16, (1<<PCINT4)
|
|
out PCMSK, r16
|
|
|
|
; init DDRB
|
|
sbi DDRB, SRCLK
|
|
cbi PORTB, RCLK ; RCLK is generally kept low
|
|
sbi DDRB, RCLK
|
|
|
|
sei
|
|
|
|
loop:
|
|
brts processbit ; flag T set? we have a bit to process
|
|
tst r1
|
|
brne sendTo595 ; r1 is non-zero? char is ready to send
|
|
rjmp loop
|
|
|
|
; Process the data bit received in INT0 handler.
|
|
processbit:
|
|
mov r16, r19 ; backup r19 before we reset T
|
|
clr r19
|
|
clt ; ready to receive another bit
|
|
|
|
; Which step are we at?
|
|
tst r18
|
|
breq processbits0
|
|
cpi r18, 1
|
|
breq processbits1
|
|
cpi r18, 2
|
|
breq processbits2
|
|
; step 3: stop bit
|
|
clr r18 ; happens in all cases
|
|
; DATA has to be set
|
|
tst r16 ; Was DATA set?
|
|
breq loop ; not set? error, don't inc R1
|
|
inc r1 ; indicate that value in r17 is good
|
|
rjmp loop
|
|
processbits0:
|
|
; step 0 - start bit
|
|
; DATA has to be cleared
|
|
tst r16 ; Was DATA set?
|
|
brne loop ; Set? error. no need to do anything. keep r18
|
|
; as-is.
|
|
; DATA is cleared. prepare r17 and r18 for step 1
|
|
inc r18
|
|
ldi r17, 0x80
|
|
clr r1
|
|
rjmp loop
|
|
|
|
processbits1:
|
|
; step 1 - receive bit
|
|
; We're about to rotate the carry flag into r17. Let's set it first
|
|
; depending on whether DATA is set.
|
|
clc
|
|
sbrc r16, 0 ; skip if DATA cleared.
|
|
sec
|
|
; Carry flag is set
|
|
ror r17
|
|
; Good. now, are we finished rotating? If carry flag is set, it means
|
|
; that we've rotated in 8 bits.
|
|
brcc loop ; we haven't finished yet
|
|
; We're finished, go to step 2
|
|
inc r18
|
|
rjmp loop
|
|
processbits2:
|
|
; step 2 - parity bit
|
|
; TODO: check parity
|
|
inc r18
|
|
rjmp loop
|
|
|
|
; send R17 to 595, MSB.
|
|
sendTo595:
|
|
tst r2
|
|
brne loop ; non-zero? 595 is "busy". Don't send.
|
|
; TODO: implement buffering. At this moment, the
|
|
; scan code is lost.
|
|
; We disable any interrupt handling during this routine. Whatever it
|
|
; is, it has no meaning to us at this point in time and processing it
|
|
; might mess things up.
|
|
cli
|
|
sbi DDRB, DATA
|
|
|
|
mov r20, r17
|
|
clr r1
|
|
ldi r16, 8
|
|
|
|
sendTo595Loop:
|
|
cbi PORTB, DATA
|
|
sbrc r20, 7 ; if leftmost bit isn't cleared, set DATA high
|
|
sbi PORTB, DATA
|
|
; toggle SRCLK
|
|
cbi PORTB, SRCLK
|
|
lsl r20
|
|
sbi PORTB, SRCLK
|
|
dec r16
|
|
brne sendTo595Loop ; not zero yet? loop
|
|
|
|
; toggle RCLK
|
|
sbi PORTB, RCLK
|
|
cbi PORTB, RCLK
|
|
|
|
; release PS/2
|
|
cbi DDRB, DATA
|
|
|
|
; Set R2 to "595 is busy"
|
|
inc r2
|
|
sei
|
|
rjmp loop
|