mirror of https://github.com/hsoft/collapseos.git
55 lines
2.3 KiB
Markdown
55 lines
2.3 KiB
Markdown
|
# Assembling Collapse OS from within it
|
||
|
|
|
||
|
|
This is where we tie lose ends, complete the circle, loop the loop: we assemble
|
||
|
|
a new Collapse OS *entirely* from within Collapse OS and write it to EEPROM,
|
||
|
|
either for another RC2014 or for an OS upgrade.
|
||
|
|
|
||
|
|
## Gathering parts
|
||
|
|
|
||
|
|
* stage4 from `sdcard` recipe. If you want to write to EEPROM as the final step,
|
||
|
|
you'll need a hybrid stage4 that also includes stuff from the `eeprom` recipe.
|
||
|
|
|
||
|
|
## Building stage 1
|
||
|
|
|
||
|
|
### Part 1
|
||
|
|
|
||
|
|
Building the first part of stage 1 (the binary part, before the inlined-source
|
||
|
|
part) from within Collapse OS is actually very similar from building it from a
|
||
|
|
modern environment. If you take the time to look at the base recipe `Makefile`,
|
||
|
|
you'll see `cat xcomp.fs | $(STAGE2)`. That command builds part 1. Open
|
||
|
|
`xcomp.fs` in a text editor and take a look at it.
|
||
|
|
|
||
|
|
To assemble stage 1 from RC2014, all you need to do is to type those commands
|
||
|
|
in the same order, and replace the `H@ 256 /MOD 2 PC! 2 PC!` lines with `H@ .X`.
|
||
|
|
Those commands will inform you of the begin/end offsets of the assembled binary.
|
||
|
|
|
||
|
|
The meaning of these commands is not explained here. You are encouraged to read
|
||
|
|
the in-system documentation for more information.
|
||
|
|
|
||
|
|
However, one thing you should know is that because the SD card driver is a bit
|
||
|
|
slow, some of these commands take a long time. Multiple minutes. Be patient.
|
||
|
|
|
||
|
|
Once all your commands are run and that you have your begin/end offset (write
|
||
|
|
them down somewhere), you're ready to assemble part 2.
|
||
|
|
|
||
|
|
### What to do on SDerr?
|
||
|
|
|
||
|
|
If you get `SDerr` in the middle of a LOAD operation, something went wrong with
|
||
|
|
the SD card. The bad news is that it left your xcomp operation in an
|
||
|
|
inconsistent state. If your at the beginning of it, it's easier to restart it
|
||
|
|
entirely.
|
||
|
|
|
||
|
|
If you're towards the end, you might want to repair it. To do so, you'll have to
|
||
|
|
bring your `XCURRENT` and `HERE` values to where they were before the LOAD
|
||
|
|
operation. You could have thought ahead and printed them before the LOAD, but if
|
||
|
|
you didn't, you'll just have to dig in your memory with `DUMP`.
|
||
|
|
|
||
|
|
You're looking at the offset of the last wordref of the *previous* LOAD
|
||
|
|
operation. That offset is going in `XCURRENT`. Then, you're looking at the end
|
||
|
|
of that word. That offset goes in `HERE`. Once you've done that, relaunch your
|
||
|
|
LOAD.
|
||
|
|
|
||
|
|
### Part 2
|
||
|
|
|
||
|
|
TODO
|