mirror of
https://github.com/hsoft/collapseos.git
synced 2024-12-26 16:58:06 +11:00
140 lines
2.7 KiB
NASM
140 lines
2.7 KiB
NASM
|
; Use this as a debug companion to at28wr. This simply dumps, TTY-escaped, the
|
||
|
|
; contents of the AT28.
|
||
|
|
;
|
||
|
|
; TODO: not always, but sometimes, the output starts with a spurious 0xFF. But
|
||
|
|
; otherwise, the rest of the contents is good, albeit offset by 1 (that is, the
|
||
|
|
; byte after the spurious 0xFF is the contents at addr 0). Weird, to fix.
|
||
|
|
|
||
|
|
.include "m328Pdef.inc"
|
||
|
|
|
||
|
|
; *** Pins ***
|
||
|
|
.equ SRCP = PORTB2
|
||
|
|
.equ SRDS = PORTB1
|
||
|
|
.equ FLWE = PORTB3
|
||
|
|
.equ FLOE = PORTB4
|
||
|
|
.equ FLCE = PORTB5 ; WARNING: same as LED
|
||
|
|
|
||
|
|
; *** Consts ***
|
||
|
|
.equ BAUD_PRESCALE = 103 ; 9600 bauds at 16mhz
|
||
|
|
|
||
|
|
rjmp main
|
||
|
|
|
||
|
|
; *** Code ***
|
||
|
|
; Sends char in r20 to UART
|
||
|
|
; Perform TTY-escape transparently.
|
||
|
|
uartwr:
|
||
|
|
lds r16, UCSR0A
|
||
|
|
sbrs r16, UDRE0 ; wait until send buffer is empty
|
||
|
|
rjmp uartwr
|
||
|
|
; should we escape?
|
||
|
|
cpi r20, 0x21
|
||
|
|
brsh uartwr_0 ; r20 >= 0x21, skip
|
||
|
|
; escape
|
||
|
|
ori r20, 0x80
|
||
|
|
ldi r16, 0x20
|
||
|
|
sts UDR0, r16
|
||
|
|
rjmp uartwr
|
||
|
|
uartwr_0:
|
||
|
|
sts UDR0, r20
|
||
|
|
ret
|
||
|
|
|
||
|
|
; send r23 to addr shift register.
|
||
|
|
; We send highest bits first so that Q7 is the MSB and Q0 is the LSB
|
||
|
|
sendaddr:
|
||
|
|
ldi r16, 8 ; we will loop 8 times
|
||
|
|
cbi PORTB, SRDS
|
||
|
|
sbrc r23, 7 ; if latest bit isn't cleared, set SER_DP high
|
||
|
|
sbi PORTB, SRDS
|
||
|
|
; toggle SRCP, not waiting between pulses. The CD74AC164 at 5V has a
|
||
|
|
; 5.9ns CP min pulse width. We can't match that at 16mhz. No need to
|
||
|
|
; wait.
|
||
|
|
cbi PORTB, SRCP
|
||
|
|
sbi PORTB, SRCP
|
||
|
|
lsl r23 ; shift our data left
|
||
|
|
dec r16
|
||
|
|
brne sendaddr+1 ; not zero yet? loop! (+1 to avoid reset)
|
||
|
|
ret
|
||
|
|
|
||
|
|
; push r20 to the rom and increase the memory counter
|
||
|
|
nextaddr:
|
||
|
|
; first, set up addr
|
||
|
|
mov r23, r21
|
||
|
|
rcall sendaddr
|
||
|
|
mov r23, r22
|
||
|
|
rcall sendaddr
|
||
|
|
inc r22
|
||
|
|
brne nextaddr_0 ; no overflow? skip
|
||
|
|
inc r21
|
||
|
|
nextaddr_0:
|
||
|
|
ret
|
||
|
|
|
||
|
|
; read EEPROM's I/O7:0 through PD7:2 and PB1:0 into r20
|
||
|
|
readdata:
|
||
|
|
cbi PORTB, FLCE
|
||
|
|
cbi PORTB, FLOE
|
||
|
|
nop ; 70ns max delay on at28
|
||
|
|
nop
|
||
|
|
nop
|
||
|
|
nop
|
||
|
|
; read bits 7:2
|
||
|
|
in r20, PIND
|
||
|
|
andi r20, 0xfc
|
||
|
|
; read bits 1:0
|
||
|
|
in r16, PINB
|
||
|
|
andi r16, 0x03
|
||
|
|
or r20, r16
|
||
|
|
sbi PORTB, FLOE
|
||
|
|
sbi PORTB, FLCE
|
||
|
|
ret
|
||
|
|
|
||
|
|
; Set PD7:2 and PB1:0 to output
|
||
|
|
ioout:
|
||
|
|
ldi r16, 0xfc ; PD7:2
|
||
|
|
out DDRD, r16
|
||
|
|
ldi r16, 0x3f ; PB5:0 (CP, WE, OE and CE too)
|
||
|
|
out DDRB, r16
|
||
|
|
ret
|
||
|
|
|
||
|
|
; Set PD7:2 and PB1:0 to input
|
||
|
|
ioin:
|
||
|
|
ldi r16, 0x03 ; PD7:2
|
||
|
|
out DDRD, r16
|
||
|
|
ldi r16, 0x3c ; PB1:0
|
||
|
|
out DDRB, r16
|
||
|
|
ret
|
||
|
|
|
||
|
|
main:
|
||
|
|
ldi r16, low(RAMEND)
|
||
|
|
out SPL, r16
|
||
|
|
ldi r16, high(RAMEND)
|
||
|
|
out SPH, r16
|
||
|
|
|
||
|
|
; We begin with WE and OE disabled (high), but CE stays enabled (low)
|
||
|
|
; the whole time.
|
||
|
|
sbi PORTB, FLWE
|
||
|
|
sbi PORTB, FLOE
|
||
|
|
sbi PORTB, FLCE
|
||
|
|
|
||
|
|
; Clear counters and flags
|
||
|
|
clr r21
|
||
|
|
clr r22
|
||
|
|
|
||
|
|
; Setup UART
|
||
|
|
ldi R16, low(BAUD_PRESCALE)
|
||
|
|
sts UBRR0L, r16
|
||
|
|
ldi r16, high(BAUD_PRESCALE)
|
||
|
|
sts UBRR0H, r16
|
||
|
|
|
||
|
|
ldi r16, (1<<TXEN0)
|
||
|
|
sts UCSR0B, r16
|
||
|
|
|
||
|
|
loop:
|
||
|
|
rcall ioout
|
||
|
|
rcall nextaddr
|
||
|
|
rcall ioin
|
||
|
|
rcall readdata
|
||
|
|
rcall uartwr
|
||
|
|
rjmp loop
|
||
|
|
|
||
|
|
|