Gather all RC2014 drivers into a single "RC2014 Recipe section"

blk/001

@@ -5,11 +5,10 @@ MASTER INDEX
 120 Linker                    140 Addressed devices
 150 Extra words
 200 Z80 assembler             260 Cross compilation
-280 Z80 boot code             350 ACIA driver
-370 SD Card driver            390 Cross-compiled core
-439 XPACKed core              480 AT28 Driver
+280 Z80 boot code             390 Cross-compiled core
+439 XPACKed core              
 490 TRS-80 Recipe             520 Fonts
-550 TI-84+ Recipe
+550 TI-84+ Recipe             580 RC2014 Recipe
 
 
 

blk/370

@@ -1,3 +0,0 @@
-SD Card driver
-
-Load range: 372-387

blk/580

@@ -0,0 +1,7 @@
+RC2014 Recipe
+
+Support code for the RC2014 recipe. Contains drivers for the
+ACIA, SD card and AT28 EEPROM.
+
+581 ACIA                       590 AT28 EEPROM
+600 SD card

blk/581

@@ -13,4 +13,4 @@ ACIA_MEM: Address in memory that can be used variables shared
           with ACIA's native words. 8 bytes used.
 
 The whole driver is cross-compilable and is loaded with
-"352 LOAD"
+"582 LOAD"

blk/590

@@ -3,4 +3,4 @@ AT28 Driver
 Write to an AT28 EEPROM while making sure that proper timing
 is followed and verify data integrity.
 
-Load with "481 LOAD"
+Load with "591 LOAD"

blk/600

@@ -0,0 +1,3 @@
+SD Card driver
+
+Load range: 602-616

recipes/rc2014/eeprom/README.md

@@ -46,7 +46,7 @@ Addressed devices are at B140. To know what you have to paste, open the loader
 block (B142) and see what blocks it loads. For each of the blocks, copy/paste
 the code in your interpreter.
 
-Do the same thing with the AT28 driver (B480)
+Do the same thing with the AT28 driver (B590)
 
 If you're doing the real thing and not using the emulator, pasting so much code
 at once might freeze up the RC2014, so it is recommended that you use

recipes/rc2014/sdcard/README.md

@@ -72,13 +72,13 @@ instead.
 
 Your Collapse OS binary needs the SDC drivers which need to be inserted during
 Cross Compilation, which needs you need to recompile it from stage 1. First,
-look at B370. You'll see that it indicates a block range for the driver. That
+look at B600. You'll see that it indicates a block range for the driver. That
 needs to be loaded.
 
 Open xcomp.fs from base recipe and locate acia loading. You'll insert a line
 right after that that will look like:
 
-    372 387 LOADR  ( sdc )
+    602 616 LOADR  ( sdc )
 
 Normally, that's all you need to do. However, you have a little problem: You're
 busting the 8K ROM limit. But it's ok, you can remove the linker's XPACKing

recipes/rc2014/xcomp.fs

@@ -13,7 +13,7 @@ RAMSTART 0x70 + CONSTANT ACIA_MEM
 
 282 LOAD  ( boot.z80 )
 393 LOAD  ( xcomp core low )
-352 LOAD  ( acia )
+582 LOAD  ( acia )
 420 LOAD  ( xcomp core high )
 (entry) _
 ( Update LATEST )