From ab6a2688fe98226f23a8f8c50c15012e375fd08b Mon Sep 17 00:00:00 2001 From: Virgil Dupras Date: Wed, 6 May 2020 12:38:33 -0400 Subject: [PATCH] recipes/trs80: self-hosting --- recipes/trs80/README.md | 58 ++++++++++++++++++++++++++--------------- 1 file changed, 37 insertions(+), 21 deletions(-) diff --git a/recipes/trs80/README.md b/recipes/trs80/README.md index 8e6a5bf..6883996 100644 --- a/recipes/trs80/README.md +++ b/recipes/trs80/README.md @@ -276,31 +276,47 @@ you're already supposed to know that one). Then, run `BYE` to return to TRSDOS just halting). Then, you can dump memory to floppy as you already did for `RECV`. -## Configuration +## Sending blkfs to floppy -In addition to the generic basic shell, this build of Collapse OS has support -for floppy drive `:1` as a block device (mapped to device `0`). Block device -commands work as expected. +As it is, your system fully supports reading and writing to floppy drive 1. It +also had `*CL<` to read a char from `*cl` and `*CL>` to emit a char to `*cl`. -In addition to this, there is a `flush` command to ensure that dirty buffers are -synced to disk. Make sure you run this after a write operation or before -swapping disks. +That's all you need to have a full Collapse OS with access to disk blocks. -On top of that, there's CFS support builtin. To enable a FS, type `fson` while -the active block device is properly placed (you can initialize a new FS by -writing `CFS\0\0\0\0` to the disk). If it doesn't error out, commands like -`fls` and `fnew` will work. Don't forget to flush when you're finished :) +First, make sure your floppies are formatted. Collapse OS is currently +hardcoded to single side and single density, which means there's a limit of 100 +blocks per disk. -There is also a custom `recv` command that does the same "ping pong" as in -`recv.asm`, but once. It puts the result in `A`. This can be useful to send down -a raw CFS: you just need a while loop that repeatedly call `recv:putb a`. +You'll need to send those blocks through RS-232. Begin by taking over the +prompt: -## Assembling programs + ' *CL> 0x53 RAM+ ! + ' *CL< 0x55 RAM+ ! -Running `make` will yield a `floppy.cfs` file that you can dump on a disk. This -CFS contains a properly configured `zasm` as well as a test `hello.asm` file. +See B80 for details about those RAM offsets. Your serial link now has the +prompt. Now, you can use `/tools/blkup` to send a disk's contents. First, +extract the first 100 blocks from blkfs: + + dd if=emul/blkfs bs=1024 count=100 > d1 + +Now, insert your formatted disk in drive 1 and push your blocks: + + tools/blkup /dev/ttyUSB0 0 d1 + +It takes a while, but you will end up having your first 100 blocks on floppy! +Go ahead, `LIST` around. Then, repeat for other disks. + +## Floppy organisation + +Making blkfs span multiple disk is a bit problematic with regards to absolute +block references in the code. You'll need to work a bit to design your very +own Collapse OS floppy set. See Usage guide (B3) for details. + +## Self-hosting + +As it is, your installment of Collapse OS is self-hosting using instructions +very similar to `recipes/rc2014/selhost`. The difference is that instead of +writing the binary you have in memory to EEPROM, you'll quit to TRSDOS with +`BYE` and use TRSDOS' `DUMP` utility to save to disk like you already did +before. -By mounting this CFS (running `fson` with the active device properly placed), -you can assemble and run a binary from `hello.asm` in the same way that you -would in any CFS-enabled shell. You'll then see those sweet "Assembled from a -TRS-80" words!