mirror of
https://github.com/hsoft/collapseos.git
synced 2024-11-30 20:58:05 +11:00
75 lines
2.8 KiB
Plaintext
75 lines
2.8 KiB
Plaintext
|
# Building a SPI relay for the z80
|
||
|
|
|
||
|
|
In this recipe, we build a SPI relay (see /doc/hw/spi.txt) for
|
||
|
|
a RC2014.
|
||
|
|
|
||
|
|
# Gathering parts
|
||
|
|
|
||
|
|
* A RC2014 Classic
|
||
|
|
* A proto board + header pins with 39 positions so we can make
|
||
|
|
a RC2014 card.
|
||
|
|
* Diodes, resistors and stuff
|
||
|
|
* 40106 (Inverter gates)
|
||
|
|
* 74xx138 (Decoder)
|
||
|
|
* 74xx375 (Latches)
|
||
|
|
* 74xx125 (Buffer)
|
||
|
|
* 74xx161 (Binary counter)
|
||
|
|
* 74xx165 (Parallel input shift register)
|
||
|
|
* 74xx595 (Shift register)
|
||
|
|
|
||
|
|
# Building the SPI relay
|
||
|
|
|
||
|
|
The schematic (img/spirelay.jpg) works well with the SD Card
|
||
|
|
subsystem (B420). Of course, it's not the only possible design
|
||
|
|
that works, but I think it's one of the most straighforwards.
|
||
|
|
|
||
|
|
This relay communicates through the z80 bus with 2 ports, DATA
|
||
|
|
and CTL and allows up to 4 devices to be connected to it at
|
||
|
|
once, although only one device can ever be active at once. This
|
||
|
|
schema only has 2 (and the real prototype I've built from it),
|
||
|
|
but the '375 has room for 4. In this schema, DATA is port 4, CTL
|
||
|
|
is port 5.
|
||
|
|
|
||
|
|
We activate a device by sending a bitmask to CTL, this will end
|
||
|
|
up in the '375 latches and activate the SS pin of one of the
|
||
|
|
device, or deactivate them all if 0 is sent.
|
||
|
|
|
||
|
|
You then initiate a SPI exchange by sending a byte to send to
|
||
|
|
the DATA port. This byte will end up in the '165 and the '161
|
||
|
|
counter will be activated, triggering a clock for the SPI
|
||
|
|
exchange. At each clock, a bit is sent to MOSI from the '161 and
|
||
|
|
received from MISO into the '595, which is the byte sent to the
|
||
|
|
z80 bus when we read from DATA.
|
||
|
|
|
||
|
|
When the '161 is wired to the system clock, as it is in the
|
||
|
|
schema, two NOPs are a sufficient delay between your DATA write
|
||
|
|
and subsequent DATA read.
|
||
|
|
|
||
|
|
However, if you build yourself some kind of clock override and
|
||
|
|
run the '161 at something slower than the system clock, those 2
|
||
|
|
NOPs will be too quick. That's where that '125 comes into play.
|
||
|
|
When reading CTL, it spits RUNNING into D0. This allows you to
|
||
|
|
know when the result of the SPI exchange is ready to be fetched.
|
||
|
|
Make sure you AND away other bits, because they'll be garbage.
|
||
|
|
|
||
|
|
The '138 is to determine our current IORQ mode (DATA/CTL and
|
||
|
|
WR/RO), the '106 is to provide for those NOTs sprinkled around.
|
||
|
|
|
||
|
|
Please note that this design is inspired by
|
||
|
|
https://www.ecstaticlyrics.com/electronics/SPI/fast_z80_interface.html
|
||
|
|
|
||
|
|
Advice 1: Make SCK polarity configurable at all 3 endpoints (the
|
||
|
|
595, the 165 and SPI connector). Those jumpers will be useful
|
||
|
|
when you need to mess with polarity in your many tinkering
|
||
|
|
sessions to come.
|
||
|
|
|
||
|
|
Advice 2: Make input CLK override-able. SD cards are plenty fast
|
||
|
|
enough for us to use the system clock, but you might want to
|
||
|
|
interact with devices that require a slower clock.
|
||
|
|
|
||
|
|
# Driving the relay
|
||
|
|
|
||
|
|
There is a provider for the SPI protocol (doc/protocol.txt) that
|
||
|
|
work with this device in B418. It needs SPI_DATA and SPI_CTL
|
||
|
|
constants which in this case are 4 and 5 respectively.
|